Search Results

Search results for "7125"

1/4 Brass Solenoid Valve 0-150 Bar 2/2 Normally Closed 1.2-5mm

1/4 inch Miniature brass solenoid valve CS Fluid Power AD8000.\nFunction: 2/2 way normally closed\nOperation: direct acting\nPort: 1/4 BSP standard, option NPT or Rc thread.\nPressure: 0 to 150 Bar (depending on orifice and coil power level)\nVacuum: Torr 10-6 Max\nBody: Brass\nInternals: stainless steel\nOrifice: 1.2 mm, 1.6 mm, 2 mm, 3 mm, 4 mm or 5 mm\nKv flow factor: 1 to 9.15 according to orifice, based on water with 1 Bar pressure drop.\nSeals: FKM standard, option EPDM, NBR, Silicone, PTFE, VST, Neoprene, ECO, HNBR or Hypalon. (PTFE must be used for pressures over 30 Bar).\nMedia: air, water, light oils, vacuum, and most other non corrosive fluids under 50CST and gases that are compatible with materials of construction.\nCoil: WPG1 12 watt UL, CSA, CE, IP67 Class H 100% duty rated DIN43650A\nCoil: WPG2 18 Watt UL, CSA, CE and IP67 Class H 100% duty rated\nCoil option: WPA3C 14.3 to 27.5 Watt (according to voltage) IP54 Class H with 30cm flying lead wires 100% duty rated.\nCoil option available AD80**: ATEX EExmIIT4 Temperature Class T4 T130°C Ex mb IIC T4 and Gb Ex mb tb IIIC T130°C Db for hazardous area 21 and 22 Pressure same as 12 Watt WPG1 coil\nVoltages: 12vDC, 24vDC, 48vDC or 24vAC, 48vAC, 110vAC or 230vAC. \nOther options: Manual Over Ride and other custom made options.

1572 in stock Model: AD8000

1 WRAS Water solenoid valve 0-10 Bar 2/2 normally closed Brass PU220D-08

1 inch WRAS approved Brass water solenoid valve PU220D-08\nFunction: 2/2 way normally closed with anti water hammer design (slowed close)\nPort: 1 BSPP thread, option NPT or Rc Thread\nPressure: 0 to 7 Bar (AC) or 0 to 5 Bar (DC Voltage) with 15 Watt Coil.\nPressure: 0 to 10 Bar with 18.5 Watt Coil.\nOperation: Assisted Lift (Zero Rated)\nTemperature: -5 °C to +90 °C Max\nBody: Brass\nInternals: stainless steel\nSeals: EPDM WRAS approved for water.\nWRAS Certificate Number 2306329.\nMedia: Water\nOrifice: 25 mm\nKv flow factor: 170.5L/Min based on water with a 1 bar pressure difference.\nCoil: 15 Watt system 13/30 Nass Magnet Class H IP65 CE DIN43650A 100% duty rated.\nCoil: 18.5 Watt system 13/36 Nass Magnet Class H IP65 CE DIN43650A 100% duty rated.\nProtection: IP65 with electrical connector (Included).\nCoil option: ATEX EExmIIT4 Temperature Class T4 T130°C Ex mb IIC T4 and Gb Ex mb tb IIIC T130°C Db for hazardous area 21 and 22 with max media temperature +80 °C and pressure 3 Bar Max.\nVoltages: 12vDC, 24vDC, 48vDC, 110vDC, 220vDC or 24vAC, 36vAC, 48vAC, 110vAC, 240vAC or 380vAC 50/60hz.\n\nWRAS Certificate Number 2306329.\nTested and approved 200,000 open and close cycles at 7 Bar with 25°C cold water, then a final 10.5 Bar pressure leak and function test.

247 in stock Model: PU220D-08

1 WRAS solenoid valve 0.3-16 Bar 2/2 Normally Closed

1 inch WRAS water solenoid valve Danfoss 132U2500 EV220BW\nFunction: 2/2 way normally closed with anti water hammer design\nOperation: Pressure assisted, requires min 0.3 bar pressure difference\nPort: 1 BSP thread\nPressure: 0.3 to 16 Bar\nBody: Brass\nInternals: stainless steel\nSeals: EPDM WRAS certified and approved\nOpening speed: 0.3 seconds and closing speed 1 second\nOrifice: 25mm\nKv flow factor: 11 m3/Hour\nCoil: DIN43650A Class H 100% duty rated\nProtection: IP65 with electrical connector (Included)\nVoltages: 12vDC, 24vDC, 24vAC, 110vAC or 230vAC\nVoltage tolerance: +/-10%\nCoil Power: DC 18 watts / AC 10 Watts

4 in stock Model: 132U2500

Coaxial 2/2 solenoid valve 0-64 Bar Brass Stainless 3/4 1 11/4 11/2 DN25

Coax solenoid valve 2 way 0-64 Bar DN25 RSG 27125\nFunction: 2/2 way normally closed, option normally open\nOperation: direct acting\nPressure: 0 to 64 Bar (0 to 16 Bar reverse flow)\nOrifice: 25mm\nKv flow factor: 205 L/Min\nPort sizes: 3/4, 1, 11/4 or 11/2 BSP thread, option NPT or flange\nBody: Brass, option stainless steel 303 or 316L\nInternals: stainless steel 316L\n\nMedia: Fluids under 500 CST and gases compatible with materials of construction. \nMedia temperature: -10°C to +100°C\n\nFluid Seals: FKM and PTFE, option NBR or EPDM.\n\nWater Seals: UHMW Polyethylene. Excellent wear and abrasion resistance. Very good lubricity in water based media. The special sharp-edged shape of the dynamic seal has a stripping effect on the piston/plunger that removes limescale + debris. Max +80°C\n\nGaseous Seals: Fluoroloy®. Excellent wear resistant material, low friction, broad chemical compatibility and provides perfect tightness performance with gaseous media. Max +80°C. \n\nIncreased leak tightness 10-5 mbar*l/sec: valve cleaned oil and grease free, special treatment of valve seat, special seal components and then a sealing tightness test with Helium.\n\nVoltages: 12vDC, 24vDC, 24vAC, 110vAC or 230vAC with other custom voltages available upon request.\nCoil: DIN43650A 100% duty rated IP65 with connector (Included)\nApprovals: TÜV, DGVM\n\nOptions: 271A25 normally closed, 271B25 normally open, manual override, inductive open and/or closed position switches with LED + 2mtr cable, various DIN43650A connectors or aluminium terminal box, mounting brackets and modular sub base mounted systems. \n\nThe 24vDC valve can be fitted with DIN43650A PWM connector (Pulse Width Modulating) a power reduction technology that reduces the holding power by up to 80% for a Greener environmentally friendly low power; low heat emission and improved thermal stability. \nOther PWM voltages available upon request.

0 in stock Model: 27125

Coaxial 3/2 Solenoid valve 0-64 Bar Brass Stainless 3/4 1 11/4 11/2 DN25

Coax solenoid valve 3 way 0-64 Bar DN25 RSG 37125\nFunction: 3/2 way normally closed, option normally open\nOperation: direct acting\nPressure: 0 to 64 Bar (0 to 16 Bar reverse flow)\nOrifice: 25mm\nKv flow factor: 205 L/Min\nPort sizes: 3/4, 1, 11/4 or 11/2 BSP thread, option NPT or flange\nBody Brass, option stainless steel 303 or 316L\nInternals: stainless steel 316L\n\nMedia: Fluids under 500 CST and gases compatible with materials of construction.\nMedia temperature: -10°C to +100°C\n\nFluid Seals: FKM and PTFE, option NBR or EPDM.\n\nWater Seals: UHMW Polyethylene. Excellent wear and abrasion resistance. Very good lubricity in water based media. The special sharp-edged shape of the dynamic seal has a stripping effect on the piston/plunger that removes limescale + debris. Max +80°C\n\nGaseous Seals: Fluoroloy® A21. Excellent wear resistant material, low friction, broad chemical compatibility and provides perfect tightness performance with gaseous media. Max +80°C.\n\nVoltages: 12vDC, 24vDC, 24vAC, 110vAC or 230vAC with other voltages available on request.\nCoil: DIN43650A 100% duty rated IP65 with connector (Included)\n\nOptions: 371A25 normally closed; 371B25 normally open, manual over ride, open and/or closed volt free position feed back switches, various DIN43650A connectors or aluminium terminal box and mounting brackets.\n\nThe 24vDC valve can be fitted with PWM (Pulse Width Modulating) connector with power reduction technology that reduces the holding power by up to 80% for a Greener more environmental friendly low power; low heat emission with improved thermal stability.\nPWM technology is available for other voltages upon request.

0 in stock Model: 37125