Solenoid valve world - 1 Plastic water solenoid valves

Media

Air

Fluid >50cSt (Non Aggressive)

Fluid >50cSt (Slight Acid/Alkali)

Gases (Non Aggressive)

Gases (Slight Acid/Alakli)

Oils + Fuels >50cSt Max

Vacuum (Low)

Water

Water (RO/Pure/Demin)

Body Material

Delrin (POM)

Nylon

Pressure Maximum

0.1 Bar (100 mBar)

0.1 Bar = 100 millibars = 1.47 psi = 1kPa

0.2 Bar (200 mBar)

0.2 Bar = 200 millibars = 2.94 psi = 20kPa

0.3 Bar (300 mBar)

0.3 Bar = 300 millibars = 4.41 psi = 30 kPa

0.4 Bar (400 mBar)

0.4 Bar = 400 millibars = 4.41 psi = 40 kPa

0.5 Bar (500 mBar)

0.5 Bar = 500 millibars = 7.36 psi = 50 kPa

0.6 Bar (600 mbar)

0.6 Bar = 600 millibars = 8.83 psi = 60 kPa

0.7 Bar (700 mBar)

0.7 Bar = 700 millibars = 10.3 psi = 70 kPa

0.8 Bar (800 mBar)

0.8 Bar = 800 millibars = 11.77 psi = 80 kPa

1 Bar

1 Bar = 1000 millibars = 14.71 psi = 100 kPa = 0.1 MPa

1.2 Bar

1.2 Bar = 1200 millibars = 17.65 psi = 1200 kPa = 0.12 MPa

1.3 Bar

1.3 Bar = 1300 millibars = 19.12 psi = 1300 kPa = 0.13 MPa

1.4 Bar

1.4 Bar = 1400 millibars = 20.59 psi = 1400 kPa = 0.14 MPa

1.5 Bar

1.5 Bar = 1500 millibars = 22.07 psi = 1500 kPa = 0.15 MPa

1.6 Bar

1.6 Bar = 1600 millibars = 23.54 psi = 1600 kPa = 0.16 MPa

2 Bar

2 Bar = 2000 millibars = 29.42 psi = 2000 kPa = 0.2 MPa

2.5 Bar

2.5 Bar = 2500 millibars = 36.78 psi = 2500 kPa = 0.25 MPa

3 Bar

3 Bar = 3000 millibars = 44.13 psi = 3000 kPa = 0.3 MPa

3.5 Bar

3.5 Bar = 3500 millibars = 51.49 psi = 3500 kPa = 0.35 MPa

4 Bar

4 Bar = 4000 millibars = 58.84 psi = 4000 kPa = 0.4 MPa

4.5 Bar

4.5 Bar = 4500 millibars = 66.20 psi = 4500 kPa = 0.45 MPa

5 Bar

5 Bar = 5000 millibars = 73.55 psi = 5000 kPa = 0.5 MPa

5.5 Bar

5.5 Bar = 5500 millibars = 80.91 psi = 5500 kPa = 0.55 MPa

6 Bar

6 Bar = 6000 millibars = 88.26 psi = 6000 kPa = 0.6 MPa

6.5 Bar

6.5 Bar = 6500 millibars = 95.62 psi = 6500 kPa = 0.65 MPa

7 Bar

7 Bar = 7000 millibars = 102.97 psi = 7000 kPa = 0.7 MPa

7.5 Bar

7.5 Bar = 7500 millibars = 110.33 psi = 7500 kPa = 0.75 MPa

8 Bar

8 Bar = 8000 millibars = 117.68 psi = 8000 kPa = 0.8 MPa

8.5 Bar

8.5 Bar = 8500 millibars = 125.04 psi = 8500 kPa = 0.85 MPa

9 Bar

9 Bar = 9000 millibars = 132.39 psi = 9000 kPa = 0.9 MPa

10 Bar

10 Bar = 147.1 psi = 1 MPa

Seals

ECO

ECO – Epichlorohydrin Rubber (Epichlorohydrin - or Herchlor, Gechron or Hydrin). excellent resistance to acids, alkali's and ozone -35°C to +125°C

EPDM

EPDM (Ethylene Propylene Diene Monomer) - known as Ethylene Propylene terpolymer, Buna-AP, Dutral, Polysar-EDM, Royalene, Vistalon, Keltan, Epcar, Nordel or Epsyn). Good for hot and drinking water, Steam, Freon refrigerant gas and Air -40°C to +120°C (+150°C steam) Poor resistance to oils + fuels

FKM (Viton)

FKM Fluoro elastomer (Fluorocarbon) Viton® Dupont registered, known as Tecnoflon, Fluorel, Dai-El. Good for hot water, acid, alkali, oils, hydrocarbons and salt solutions, many aggressive chemicals, diluted acids, weak alkali's, mineral oils, aliphatic and aromatic hydrocarbons, chlorinated hydrocarbons, sunlight and ozone. -26°C to +205°C. Poor resistance to Ketone's and Acetone.

HNBR

HNBR (Hydrogenated Nitrile Butadine Rubber) also known as Therban, Zetpol or Tornac). Good for motor oils, sour gas, amine oil mixtures, oxidised fuels, lubricating oils, mineral based hydraulic oil, animal and vegetable oil, diesel fuel, ozone, dilute acids and bases, new bio-oils, H2S Hydrogen Sulphide and C02 carbon dioxide. -40°C to +150°C. Poor for concentrated alkali's, esters, alkyl phosphate, ethers, halogenated solvents, ketone's, halogenated hydrocarbons, solvents and flames.

Hypalon

Hypalon is a chlorosulfonated polyethylene (CSPE) synthetic rubber (CSM). Good for chemicals, ozone, ultraviolet light, oxidising agents, hot water, corrosive chemicals, low gas permeability, good electrical properties, low flammability. -35°C to +125°C. Poor to fair fuel resistance and its low temperature properties are generally limited.

NBR

NBR (Nitrile Buna Rubber) known as Nitrile Butadine, Buna-N, Hycar, Chemigum, Butakon, Breaon, Butacril, Paracil, Nipol, Perbunan, Krynac or Europrene-N. Good for Aliphatic Hydrocarbons, Petroleum, Fuels, Mineral Oil, Vegetable and Hydraulic Oil, Alcohol and many Acids. -35°C to +100°C. Poor for Ozone, Acetone, Methyl ethyl Ketone, Chlorinated Hydrocarbons, Ethers and Esters.

Silicone

Silicone (VMQ) known as PVMQ, Silastic, Siloprene, Rhodorsil or Silplus. Good resistance to Oil, solvents, aniline alcohol, dilute acids or bases, benzene, toluene, petrol. -60°C to +230°C. Poor resistance Diesel, hot air, steam over 150 C, strong acids and bases.

VST

VST (Viton-Silicone-Teflon). Has enhanced chemical resistance compared to Viton, especially against aggressive chemicals like ketones, esters, and some organic acids. Combines the properties of Viton, silicone, and Teflon, offering improved flexibility, compression set resistance, and low-temperature performance compared to standard Viton. -40°C to 200°C

Approvals

ATEX Zone II GD

hazardous area classification indicating a potentially explosive atmosphere with gases and dust present, requiring specific equipment for safe operation.

ATEX Exm

ATEX Protection by encapsulation ll 2 G Ex mb ll T4 Gb and ll 2 D Ex tb IIIC T130°C Db IP65

IP54

Dust protected and protected against splashing water

IP65

Dust tight and protected against water jets

IP67

Dust protected and protected against immersion in water

CSA

CSA approval certifies products for safety and performance, conducted by the Canadian Standards Association.

UL

UL (Underwriters Laboratories) approval indicates that a product has met safety standards set by UL for electrical devices and components.

Orifice

25mm

Valve orifice or sealing face with diameter 25mm

28mm

Valve orifice or sealing face with diameter 28mm

Operation

Assisted Lift

Assisted lift solenoid valve assists in opening against pressure, ensuring reliable operation from vacuum to medium pressure systems.

Pressure Assisted

Operate via pilot pressure control and require a minimum pressure difference between inlet and outlet from 0.5 Bar.

Voltage

12vDC

12 volts Direct Current

24vDC

24 volts Direct Current

24vAC

24 volts 50/60Hz Alternating Current

48vAC

48 volts 50/60Hz alternating current

48vDC

48 volts Direct Current

110vAC

110 volts 50/60Hz Alternating Current

230VAC

230 volts 50/60Hz Alternating Current

Options required

Mounting Holes

Supplied with additional threaded holes typically in the base, typically for securing to a baseplate.

Shading Ring - Silver

The copper shading ring in the solenoid tube has been replaced with silver. Typically used for RO water and aggressive media applications.

Only Show Items In Stock

Show spare parts

1 Plastic water solenoid valves - Normally Open

Filter Products

35 IN STOCK

28 IN STOCK