Key Features
✓ Nass Magnet DIN2R-230V
✓ DIN 43650 Form A Connector
✓ EN 175301-803 Form A
✓ Standard 18mm Pin Spacing
✓ 2 Pins + Earth Connection
✓ 230V AC Rated Input
✓ Full Wave Bridge Rectifier
✓ AC to Rectified DC Conversion
✓ Integrated VDR Protection
✓ Maximum Current 1 Amp
✓ PG9 Cable Entry
✓ 6–8mm Cable Diameter
✓ 0.5–1.5mm² Wire Capacity
✓ IP65 Protection When Fitted
✓ Black PA6 GF30 Housing
✓ Clear Connector Cover
✓ NBR Cable & Cover Seals
✓ Tin Plated Brass Contacts
✓ Zinc Plated Fixing Screw
✓ Temperature -25°C to +125°C
✓ Compatible DC Solenoid Coils
✓ Industrial Valve Applications
Datasheets
Description
DIN Form A Bridge Rectifier Connector 230V AC – PG9 IP65 – Nass Magnet
The Nass Magnet DIN2R-230V is a DIN 43650 Form A electrical connector featuring an integrated full-wave bridge rectifier and VDR varistor surge protection. Designed for compatible solenoid valves and electromagnetic coils, this connector converts a 230V AC supply into rectified DC, allowing suitable DC solenoid coils to operate from an AC power source.
Featuring the standard 18mm DIN Form A contact arrangement, a PG9 cable entry and IP65 protection when correctly fitted, the DIN2R-230V provides a compact electrical connection for industrial solenoid valve applications.
Its integrated rectifier eliminates the need for a separate external bridge rectifier, while the VDR varistor helps suppress voltage transients generated during solenoid switching.
Integrated Full-Wave Bridge Rectifier
The DIN2R-230V incorporates a full-wave bridge rectifier that converts an AC input into pulsating DC.
Input Supply: 230V AC
Rectifier Type: Full-Wave Bridge
Output: Rectified DC
Circuit Protection: Integrated VDR Varistor
The rectifier enables compatible DC solenoid coils to be powered from an AC supply without requiring a separate external rectifier module.
The rectified output is not a regulated DC supply. Coil compatibility, voltage rating and power requirements must be confirmed before installation.
VDR Surge Protection
An integrated voltage-dependent resistor (VDR) provides transient voltage suppression for the solenoid circuit.
When an inductive solenoid coil is switched off, the resulting voltage transient can affect electrical contacts and associated control equipment.
The VDR helps limit these voltage spikes, providing additional protection for the electrical circuit.
The connector combines rectification and surge suppression in one compact assembly.
DIN 43650 Form A Compatibility
The DIN2R-230V uses the standard DIN 43650 Form A electrical interface, also referenced as EN 175301-803 Form A.
Connector Type: DIN Form A
Pin Spacing: 18mm
Contact Arrangement: 2 Pins + Earth
Applicable Standards: DIN 43650A / EN 175301-803
The connector is suitable for compatible solenoid valve coils and electromagnetic actuators using the 18mm Form A interface.
It is not interchangeable with smaller DIN Form B or Form C connectors.
Housing & Construction
Housing Material: Black Polyamide PA6 GF30
Cover: Clear
Contacts: CuZn, Tin-Plated
Central Fixing Screw: Steel, Zinc-Plated
Cable Entry: PG9
Cable Grommet: NBR
Gasket: NBR
The glass-fibre-reinforced polyamide housing provides mechanical durability for industrial applications.
The connector is supplied with the appropriate sealing components for installation onto compatible DIN Form A solenoid coils.
Electrical Specification
Model: DIN2R-230V
Rated Voltage: 230V AC
Maximum Current: 1 Amp
Circuit: Full-Wave Bridge Rectifier + VDR
Maximum Voltage Drop: 3mV (as stated in the existing specification)
Maximum Power Consumption: 5mA (as stated in the existing specification)
Maximum Resistance: 4mΩ
The voltage drop and consumption figures above should be checked against the original manufacturer datasheet, as their stated units are unusual for these electrical characteristics.
Cable Entry & Sealing
Cable Entry: PG9
Cable Diameter: 6–8mm with Standard Grommet
Alternative Cable Entry: M20 × 1.5mm with Grommet Removed
Sealing Components: NBR Grommet and Gasket
Ingress Protection: IP65 When Correctly Installed
Maximum Wire Cross-Section: 0.5–1.5mm²
The connector must be correctly assembled with suitable cable sealing and gasket compression to achieve the specified ingress protection.
Operating Temperature
Operating Temperature: -25°C to +125°C
The connector is designed for industrial electrical installations within the specified temperature range.
The permissible operating temperature of the complete assembly will also depend on the connected solenoid coil and installation conditions.
Typical Applications
230V AC Solenoid Valve Circuits
Compatible DC Solenoid Coils
Industrial Automation Equipment
Electromagnetic Actuators
Pneumatic Solenoid Valves
Process Control Equipment
OEM Machinery
Solenoid Coil Replacement and Maintenance
Applications Requiring Rectified DC
Technical Specification
Manufacturer: Nass Magnet GmbH
Model: DIN2R-230V
Connector Type: DIN 43650 Form A
Standard: EN 175301-803 Form A
Contact Arrangement: 2 Pins + Earth
Pin Spacing: 18mm
Rated Voltage: 230V AC
Maximum Current: 1A
Circuit: Full-Wave Bridge Rectifier
Surge Protection: Integrated VDR Varistor
Housing Material: PA6 GF30 Polyamide
Housing Colour: Black
Cover: Clear
Cable Entry: PG9
Cable Diameter: 6–8mm
Optional Entry Arrangement: M20 × 1.5mm
Wire Cross-Section: 0.5–1.5mm²
Seals: NBR
Contacts: Tin-Plated CuZn
Fixing Screw: Zinc-Plated Steel
Ingress Protection: IP65
Operating Temperature: -25°C to +125°C
Why Choose the Nass Magnet DIN2R-230V?
The DIN2R-230V combines a full-wave bridge rectifier, VDR surge protection and a standard DIN Form A electrical connection in one compact industrial connector.
Its integrated circuit provides a convenient method of supplying rectified DC to compatible solenoid coils from a 230V AC source, while the PG9 cable entry, reinforced polyamide housing and IP65 protection make it suitable for industrial valve installations.
Free Next Day UK Delivery.
Related Products & Categories
DIN 43650 Electrical Connectors
Solenoid Coils & Magnets
Technical Specification
Brand: Nass Magnet GmbH
Model: DIN2R-230v
Width: 28.00 mm
Height: 31.00 mm
Depth: 28.00 mm
Weight: 0.05 kg
Voltage: 110vAC, 230VAC, 24vAC
Approvals:: IP65
Spares (Coils, Connectors, Seals): DIN connector Form A
Found in these Categories
Electrical Connector Form A Bridge Rectifier PG9 230v IP65
£6.35 incl. VAT £5.29 ex. VAT
-19% Was £7.82 incl. VAT
