Key Features
- DIN 43650 Form A Connector
- Pre-Wired 3 Metre Cable
- Green LED for AC Operation
- Red LED for DC Operation
- Bipolar AC/DC LED Circuit
- 10–61V or 61–250V Options
- 10A Maximum Current
- 250V Maximum Voltage
- 2 Pin + Protective Earth
- Standard 18mm Contact Spacing
- 3 Core 0.75mm² Cable
- IP65 Protection
- PA6 GF30 Terminal Block
- Zinc-Plated CuZn Contacts
- Ready-Wired for Installation
Description
Pre-Wired DIN 43650 Form A Connector 3m Cable AC/DC LED – IP65
Pre-wired DIN 43650 Form A electrical connector with integrated bipolar AC/DC LED indication and a factory-fitted 3 metre 3-core cable, designed for quick and reliable connection of solenoid valves and industrial control equipment.
The integrated dual-colour indication provides a green LED when operating on AC and a red LED when operating on DC, allowing the type and presence of the electrical supply to be identified directly at the solenoid valve.
Available in 10–61V and 61–250V versions, the connector is rated for up to 10A maximum current and 250V maximum voltage.
The connector is supplied ready-wired with a 3 metre black 3-core 0.75mm² cable, eliminating the need to assemble the DIN connector, terminals, seals and cable gland on site. IP65 environmental protection makes it suitable for general industrial automation and fluid-control applications.
Available Voltage Ranges
Two voltage-range options are available:
10–61V Version
Suitable for low-voltage AC or DC solenoid valve applications within the specified 10–61V range.
61–250V Version
Suitable for higher-voltage AC or DC solenoid valve applications up to 250V.
Maximum current: 10A
Maximum voltage: 250V
This wide-range approach reduces the need for separate voltage-specific connectors across commonly used industrial solenoid valve supplies.
AC Green / DC Red LED Indication
The integrated bipolar LED circuit provides an especially useful visual indication:
AC supply → Green LED
DC supply → Red LED
The AC circuit is suitable for 50/60Hz operation.
This allows engineers to quickly identify both the presence and type of electrical supply directly at the solenoid valve during commissioning, maintenance and fault finding.
Pre-Wired 3 Metre Cable
The connector is supplied complete with a factory-fitted 3 metre black electrical cable, reducing installation time compared with conventional field-wired DIN connectors.
Cable specification:
Length: 3 metres
Cable: 3 core
Conductor size: 0.75mm²
Cable type: H05WF PVC
Core colours:
✓ Brown
✓ Blue
✓ Green / Yellow
Cable stripping: 30mm
The pre-wired construction provides a convenient ready-to-install solution for OEM machinery, replacement valves and industrial automation installations.
Electrical Specification
Connector type: DIN Form A
Standard: DIN 43650A
Contact spacing: 18mm
Poles: 2 + protective earth
Voltage ranges: 10–61V or 61–250V
Maximum voltage: 250V
Maximum current: 10A
AC frequency: 50/60Hz
AC indication: Green LED
DC indication: Red LED
Circuit: Bipolar AC/DC LED
Construction
Terminal block material: PA6 GF30
Contacts: CuZn, zinc plated
Contact spacing: 18mm
Protective earth position: 6h / 12h
Cable: 3-core 0.75mm²
Cable length: 3 metres
Protection: IP65
IP65 Protection
The moulded pre-wired construction provides IP65 ingress protection, making the connector suitable for general industrial environments where protection against dust and water jets is required.
The factory-fitted cable also removes the need to terminate and seal a separate cable gland during installation.
DIN 43650A Form A Connection
The connector uses the widely adopted DIN 43650A Form A electrical interface with 18mm contact spacing.
This standard connection is commonly found on industrial solenoid valves and coils used for pneumatic, hydraulic, water and general fluid-control applications.
Its pre-wired construction makes it particularly useful where installation speed, consistent wiring and reduced on-site assembly are important.
Typical Applications
✓ Solenoid valves
✓ Pneumatic control valves
✓ Hydraulic solenoid valves
✓ Water control valves
✓ Process control equipment
✓ Industrial automation
✓ OEM machinery
✓ Packaging equipment
✓ Pumps and fluid systems
✓ Replacement valve wiring
✓ Machine building
✓ Control systems
Why Choose a Pre-Wired DIN Connector?
A conventional DIN connector requires the installer to select the correct cable, prepare the conductors, wire the terminal block and correctly assemble the connector and cable gland.
This version arrives pre-wired with a 3 metre cable, providing a convenient ready-to-install connection.
The integrated green AC / red DC LED indication also provides immediate visual confirmation of electrical operation, while the two wide voltage ranges cover a broad selection of industrial solenoid valve applications.
With a 10A maximum rating, 18mm DIN Form A interface and IP65 protection, it provides a practical electrical connection for OEM, maintenance and general industrial applications.
Related Products & Categories
Technical Specification
Brand: Connexion
Model: DIN2-LED
Width: 28.00 mm
Height: 31.00 mm
Depth: 28.00 mm
Weight: 0.40 kg
Voltage: 12vDC, 12vAC, 24vDC, 24vAC, 36vAC, 48vAC, 48vDC, 110vAC, 110vDC, 125vDC, 230VAC, 200vDC
Spares (Coils, Connectors, Seals): DIN connector Form A
Approvals:: IP65
Found in these Categories
Electrical Connector Form A prewired 3 mtr LED 0-250v IP65
£6.97 incl. VAT £5.81 ex. VAT
-30% Was £9.96 incl. VAT