Air Operated angle seat piston valves also known as Air Actuated Globe or Y pattern valves suitable for air, water, oil, grease, vacuum, steam, viscous fluids, acids and alkali's.

Air actuated ball valves, coaxial valves and angle valves are Controlled Via a compressed air supply Instead Of An Electrical Supply can be either single acting (fail safe return) or double acting (air to open and close) suitable for most applications.

Breathing air filters including coalescing and activated carbon air filters and filter regulator combination sets.

Pneumatic non return valves and silent full flow check valves with silent noiseless directional flow control with anti water hammer design.

Search Our 2/2 & 3/2 Way Electrically and Air Operated Coaxial Valves manufactured in Brass, Steel and Stainless Steel.

Dust Collecting Valves also known as Pulse Jet Diaphragm Valves for dust collectors, gas turbine filtration systems, environmental equipment and desulfurization equipment for reverse pulse jet filter cleaning of air bag filters, emvelope filters, ceramic filters and sintered metal fibre filters.

Yellow Emergency Stop Button Red/Twist Reset Mushroom Head E-Stop. 400V 10 Amp CE rated - Strike RED knob will cut electrical supply, rotating knob clockwise resets the switch. Includes 1x normally closed and 1x normally open 400 volt rated CE Switch. Available twist reset, twist reset with key and twist reset with Guard.

High speed solenoid valves 2000 cycles a minute Width 10mm or 15mm, Function 3/2 or 5/2 way manufactured with low power 0.8 Watt, 1 Watt or 2.5 Watt coils, Pressure 0 to 8 or 0 to 10 Bar suitable for clean compressed air.

Ball float valves for mechanical water tank level control. They work by rising water level in the tank that lifts the ball to shut off the water refill, when water level and then ball drops reopening the valve to refill the tank.

Threaded and flanged ductile iron and stainless steel foot strainer valves for water inlet protection on suction systems with filter screen, internal check valve that protects against loss of suction and aids in pump priming reducing suction pump run dry time and incorporates a lever operated back flush mechanism.

Sub Base mounted solenoid valves sharing a common manifold or inlet allow for individual outlet control are manufactured from Plastic, Brass and Stainless Steel either 2/2, 3/2 and 5/2 way for pressures ranging from vacuum up to 150 Bar.

2/2; 3/2; 4/2; 4/3; 5/2 and 5/3 way mechanical pneumatic control valves with roller, twist selector, mushroom palm button, detent button or push pull button or lever for compressed air 0 to 9 Bar.

Pilot Float valves for mechanical water tank level control, work in conjunction with Float Ball Valve for reliable mechanical water tank refilling. NO need for electrics. Manufactured from Ductile Iron or Stainless steel.

Pneumatic control foot pedal air control valve 3/2 or 5/2 function, spring return or detent (lock) with or without foot guard.

Pressure Reducing Valves (PRV), Pressure Sustaining Valves (BPV) and Pressure Relief Valves (PLV).

Proportional solenoid valve 1/8" or 1/4" BSP/NPT port function 2/2 way manufactured from Brass, Stainless steel or Aluminium, Pressure 1 to 16 Bar with 24 volt proportional opening according to 100 to 500 milliamp signal.

Push in fittings for fast connection of pneumatic nylon and polyurethane tube to tube or tube to thread.

90 Degree Solenoid Valves available in different sizes and voltages.

Sub Base Mount Solenoid Valves that can be fitted or mounted to a manifold system that will share a common inlet or outlet.

Cycle timers for solenoid valves and timer control motor ball valves including repeat, single shot, delay and digital programmable timers from 0.5 Seconds to 59 hours. Designed for fully automated ON/OFF open/close control for fluid and gas systems.

Nylon and Polyurethane tubing for pneumatic systems.

Air vent bleed vacuum release valves threaded or flange Cast Iron or stainless steel are designed to vent air and prevent vacuum also known as an Air and Vacuum Release Valves.

Water hammer arrestors designed to absorb and remove water hammer banging, thumping, clanking and rattling caused by water hammer shock waves.

Y Pattern filters and strainers designed to remove debris from liquids manufactured from stainless steel, pressures 0 to 55 Bar, Seals PTFE, Temperature -29C to +232C.

Spare Solenoid Valves Armature Assemblies, 2/2 way normally closed; 2/2 way normally open with copper or silver shading ring, 3/2 way normally closed sealing with NBR, Viton, EPDM or PTFE manufactured from Brass or Stainless Steel. Includes Nass Magnet system 8 and system 13 assemblies.

Solenoid coils according to bore diameter, dimensions, power level and voltage including IP54, IP65, IP67, IP68 and ATEX zone 21 and zone 22 protection either Class F Class H and Class N DIN43650A,B and flying lead wire.

DIN43650A Form A 28mm square, Industrial Form B 21x28.5mm and Micro C 15.6x15.6mm Connectors with or without circuits LED, VDR, Rectified and pre-wired filed mountable electrical connectors.

PWM Coil Protector and heat reducing energy saving adapters. Pulse Width Modulating connectors allow full microsecond power when switched on (inrush power) and then drop power after valve has moved (holding power)so valve stays in powered position but power consumption and heat are greatly reduced.

Spare filter elements 5 and 50 micron PE, Sintered Bronze and Coalescing and Activated Carbon filter elements, Manual, Semi and fully automatic drains and Polycarbonate, Acid/Alkali Resistant and Aluminium Bowls.

Spare Diaphragms manufactured from NBR, EPDM and Viton to suit brass and stainless steel solenoid valves.

Permanent Magnets for solenoid valves - Great engineering tool that can replace the electro magnetic (coil) with this permanent magnet. Ideal for commissioning and testing solenoid valves where no electrical supply is available or as manual over ride. The SVOM - Solenoid Valve Operating Magnet.

Protective Solenoid Valve cover to suit RPE plastic latching 2/2 way solenoid valves.

Metal and Stainless Steel Pressure Gauges 1/8 and 1/4 inch rear entry 42mm and 53mm diameter with pressure ranges 0-10 Bar, 0-20 Bar and 0-30 Bar.

Mounting Kits for Shako PU320 & PU300, manifolds for Shako BM520 pneumatic valves.