Solenoid valve world

General Valves WRAS Natural Gas Wizard Ball Valves Pneumatics Contact Us

Home
Other products

Other Products

Search Air actuated + angle seat valves; coaxial, pulse, solenoid coils; connectors + seal kits, pressure transmitters + switches, magnets, timers, water leak detection + much more.

Show Sub Categories

Air Operated angle seat piston valves also known as Air Actuated Globe or Y pattern valves suitable for air, water, oil, grease, vacuum, steam, thick viscous fluids, acids and alkali's.

Angle Seat Piston Valves

Pneumatic non return valves and silent full flow check valves with silent noiseless directional flow control with anti water hammer design.

Check - Non Return Valves

Coaxial Solenoid and Air Operated 2/2 and 3/2 way valves in Brass and 304 + 316L stainless steel 1/4 to 2 inch for pressures up to 300 Bar.

Coaxial Valves

Dust Collecting Valves, Pulse Jet Diaphragm Valves for dust collectors, gas turbine filtration systems, environmental equipment and desulfurization equipment for reverse pulse jet filter cleaning of air bag filters, envelope filters, ceramic filters and sintered metal fibre filters.

Dust Pulse Valves

Emergency stop isolation electric buttons, air valves, soft start valves and switch boxes.

Emergency Stop Devices

Y Pattern filters and strainers designed to remove debris from liquids manufactured from stainless steel, pressures 0 to 55 Bar, Seals PTFE, Temperature -29C to +232C.

Filters - Y Pattern

Pilot Float valves for mechanical water tank level control, that operate via an external controller or Float Ball Valve for reliable mechanical water tank refilling without electrical input. Manufactured from Ductile Iron or Stainless steel.

Float Operated Valves

Foot strainer valves for water inlet protection for suction systems includes filter screen, internal check valve protecting against loss of suction and aids in pump priming reducing suction pump run dry time and incorporates a lever operated back flush system.

Foot Suction Prime Aid Valves

Water leak detection systems automatically shut off water supply when water leaks are detected, with alarm.

Leak Detection Systems

Permanent Magnets for solenoid valves - Great engineering tool that can replace the electro magnetic (coil) with this permanent magnet. Ideal for commissioning and testing solenoid valves where no electrical supply is available or as manual over ride. Our SVOM - Solenoid Valve Operating Magnet.

Magnets for Solenoid Valve Commissioning

Search pressure gauges, pressure transmitters + pressure switches.

Pressure Gauges, Transmitters + Switches

Proportional valves also known as modulating valves that open in direct proportion to the control voltage applied, choose 0 to 10 volt or 4 to 20 Milliamp.

Proportional Control Valves

All Spare Parts

Cycle timers, condensate drain valves and timer control motor ball valves including repeat, single shot, delay and digital programmable timers from 0.5 seconds to 59 hours. Designed for fully automated ON/OFF open/close control for fluid and gas systems.

Timers, Timed Valves + Drains

Polyurethane tubing, 100 + 200 MTR rolls, metric or imperial sizes up to 16mm in all colours.

Tubing - Polyurethane

Vacuum release valves designed to vent air and prevent vacuum also known as an Air and Vacuum Release Valves, Cast Iron or stainless steel, sizes 1/2 to 1 inch thread.

Vacuum Breaker Air Vent Valves

Shako VV Vacuum generators utilise compressed air (1 to 6 Bar) to generate vacuum to -91.8 Kpa, sizes 1/8, 1/4 or 3/8.

Vacuum Generators

Water hammer arrestors designed to absorb and remove water hammer banging, thumping, clanking and rattling caused by water hammer shock waves.

Anti Water Hammer Valves

Solenoid valve discounted and end of line items that are still new and unused. When the stock is gone - its gone.
Please feel free to ask for an even better price.

Clearance + Bargains

Free promotional gifts for qualifying online store orders. You can always buy more.

Fun Items + Giveaways

Filters

Price

Valve / Product Type

Air Actuated Valve0

air actuated valves that utilise a compressed air supply to operate.

Air Filters Regulators & Oilers 0

Air pressure regulator with air filter with air lubrication system. Provides stable outlet pressure whilst removing debris and 90% moisture the finally providing oil mist to lubricate downstream equipment.

AirLine Fittings + Tube0

compressed air line tubing and push to connect fittings

Angle Seat Valve0

Angle seat piston valves, air actuated globe valves.

Ball Valve0

Motor and air actuated quarter turn 2+3 way ball valves

Breathing & Coalescing Air Filters0

Removes all particulates, moisture, oil, vapour and odour for technically absolutely clean air for the highest demanding air applications.

Check Valve0

Check + non return valves only allow flow in one direction

Coaxial Valve0

Condensate drain0

Automated + time control drain valves

Filters0

Filters designed to remove particulate or debris from gases or fluids.

Float Valves0

Leak Detection0

Valves and systems designed to automatically detect any water leak and automatically close the water supply valve to prevent damage.

Manual + Mechanical Control0

Air valves that are controlled manually and mechanically

Motor Actuated 0

Pressure Switch / Transmitter0

Pressure switches and pressure transmitters

Pressure Reducing0

Pressure reducing valves (PRV) reduce and maintain stable outlet pressure

Pressure Relief0

Safety pressure relief / pressure limiting valve (PLV), stays closed until pressure reaches set pressure - then quickly opens, releasing any excess pressure.

Pressure Sustaining0

Pressure sustaining / back pressure valve, maintains a minimum preset upstream (Inlet) pressure, valve will close if pressure drops to set pressure and reopens when inlet pressure increases again.

Proportional Modulating0

Flow regulating valves with manual or electric modulating 4-20mA control.

Pulse0

Pulse dust valves, air + solenoid actuated

Quick Exhaust0

Will instantly open outlet to exhaust when the inlet pressure drops to greatly increase cylinder reaction speed.

Safety Shut Off0

Safety shut off isolation valve, shuts off and secures air line systems, will vent downstream air when closed.

Soft Start0

Electric open and close control for airline systems, power off downstream air is vented to atmosphere - power on opens slowly to prevent sudden pressure surges.

Solenoid Valve0

Valves controlled by electrical signal via a solenoid or electro magnet.

Timed control0

Time control valves can be set to activate according to preset intervals when power is applied.

Vacuum breaker/ Air release 0

valves that release trapped air and vacuum

Vacuum Generator0

Vacuum generators utilise compressed air (1 to 6 Bar) to generate vacuum to -91.8 Kpa, sizes 1/8, 1/4 or 3/8.

Water Hammer Arrestor0

Water hammer arrestors designed to absorb and remove water hammer banging, thumping, clanking and rattling caused by water hammer shock waves.

Push In Elbow / Banjo0

Male and female BSP and metric pneumatic push to connect elbow fittings

Push In Flow & Speed Control0

Push fittings with flow or speed control for compressed airlines

Push In Multi Port & Manifold0

Multi Port + Manifold Push In Fitting Systems

Push In Plugs/ Caps + Reducers0

Push in blank Caps/ Plugs and reducing fittings

Push In Studs0

Male and female BSP and metric Stud pneumatic push to connect fittings

Push In Tee's / Y's0

Male BSP and metric pneumatic push to connect T and Y type airline fittings

Push In Unions0

Male and female BSP and metric union pneumatic push to connect fittings

Port Size

4mm0

M50

1/8 thread0

valves with 1/8 inch threaded ports

1/4 thread0

valves with 1/4 inch threaded ports

6mm0

8mm0

3/8 thread0

valves with 3/8 inch threaded ports

3/8 Flange DN100

3/8 Push Fit0

10mm0

12mm0

1/2 thread0

valves with 1/2 inch threaded ports

1/2 inch Flange DN150

15mm0

3/4 thread0

valves with 3/4 inch threaded ports

3/4 Flange DN200

20mm0

1 thread0

valves with 1 inch threaded ports

1 inch Flange DN250

22mm0

25mm0

28mm0

11/4 thread0

valves with 11/4 inch threaded ports

11/4 inch Flange DN320

32mm0

11/2 thread0

valves with 11/2 inch threaded ports

11/2 inch Flange DN400

40mm0

2 thread0

valves with 2 inch threaded ports

2 inch Flange DN500

50mm0

63mm0

21/2 thread0

valves with 21/2 inch threaded ports

21/2 inch Flange DN65 0

3 thread0

valves with 3 inch threaded ports

3 inch Flange DN80 0

4 Inch0

4 inch Flange DN100 0

5 inch Flange DN125 0

6 inch Flange DN150 0

8 inch Flange DN200 0

10 inch Flange DN2500

12 inch Flange DN300 0

14 inch Flange DN350 0

16 inch Flange DN400 0

18 inch Flange DN450 0

20 inch Flange DN500 0

Sub Base Mount0

Media

Air0

Fluid (Non Aggressive)0

Fluid (Slight Acid/Alkali)0

Fluid (Stong Acid/Alkali)0

Fluid Thick 51>500cSt0

Gases (Non Aggressive)0

Gases (Slight Acid/Alakli)0

Gases (Strong Acid/Alkali)0

Natural Gas0

Oils + Fuels 50cSt Max0

Steam0

Vacuum (Low)0

Vacuum (Medium)0

Vacuum (High)0

Water0

Water (RO/Pure/Demin)0

Body Material

Aluminium0

Brass0

Bronze0

Cast Iron0

Delrin (POM)0

Ductile Iron0

Nylon0

Polycarbonate0

Polyethylene0

Polypropylene0

Polyurethane0

PVC0

PTFE0

Steel0

Stainless Steel0

UPVC0

Function

2/2 Normally Closed0

2 ports (inlet/outlet) with 2 positions (Open/Closed) - valve stays closed (Failsafe) requires power to open

2/2 Normally Open0

2 ports (inlet/outlet) with 2 positions (Open/Closed) - valve stays open (Failsafe) requires power to close

2/2 Latching0

2 ports (inlet/outlet) with 2 positions (Open/Closed) - short power pulse valve stays open - reverse power pulse valve stays closed

2/2 Double Acting0

2 ports (inlet/outlet) with 2 positions (Open/Closed) - power or air one side to move - power or air opposite side to return.

3/2 Normally Closed0

3 ports with 2 positions. Power off inlet closed, outlet open to exhaust - power on inlet open to outlet with exhaust closed.

3/2 Normally Open0

3 ports 2 positions. Inlet open to outlet with exhaust closed - power on inlet closed with outlet open to exhaust.

3/2 Universal0

3 ports, 2 positions flow can be in any direction. Can be piped as 3/2 normally closed flow into inlet, 3/2 normally open flow into exhaust, 3/2 diverting flow into outlet.

3 way T Port0

3 way L Port0

4/2 Way0

A 4/2 way valve has four ports and two positions. It controls the direction of flow by switching between two paths in a pneumatic or hydraulic system.

4/3 Way0

A 4/3 way valve has four ports and three positions. It controls the direction of flow by switching between two paths in a pneumatic or hydraulic system with third option all ports closed.

5/2 Single Acting0

5 ports 2 positions (1 inlet, 2 outlets, 2 exhaust ports). Power to coil Cylinder fully extends - Power off cylinder fully retracts (or visa versa)

5/2 Double Acting0

Power to left coil Cylinder fully extends, power to right coil cylinder fully retracts, power off cylinder stays put fully extended or retracted.

5/3 Way0

Power to left coil cylinder extends, power to right coil cylinder retracts, power off cylinder stays put even in a mid position.

Power Open/Power Close0

Valve requires power to open and power to close, no power valves stays in position.

Proportional / Modulating0

Valve opens proportionally according to signal input, either 4-20mA, 0-10v or 0-5 volt. Example 4mA valve closed, 8mA 25% open, 12mA 50% open, 18mA 75% open and 20mA fully open.

Pressure

Vacuum0

Vacuum products including valves, filters, regulators for vacuum and high vacuum systems down to -101Kpa.

0.02 Bar (20 mBar)0

0.02 Bar = 20 millibars = 0.29psi = 2 Kpa

0.1 Bar (100 mBar)0

0.1 Bar = 100 millibars = 1.47 psi = 1kPa

0.2 Bar (200 mBar)0

0.2 Bar = 200 millibars = 2.94 psi = 20kPa

0.3 Bar (300 mBar)0

0.3 Bar = 300 millibars = 4.41 psi = 30 kPa

0.4 Bar (400 mBar)0

0.4 Bar = 400 millibars = 4.41 psi = 40 kPa

0.5 Bar (500 mBar)0

0.5 Bar = 500 millibars = 7.36 psi = 50 kPa

0.6 Bar (600 mbar)0

0.6 Bar = 600 millibars = 8.83 psi = 60 kPa

0.7 Bar (700 mBar)0

0.7 Bar = 700 millibars = 10.3 psi = 70 kPa

0.8 Bar (800 mBar)0

0.8 Bar = 800 millibars = 11.77 psi = 80 kPa

1 Bar0

1 Bar = 1000 millibars = 14.71 psi = 100 kPa = 0.1 MPa

1.2 Bar0

1.2 Bar = 1200 millibars = 17.65 psi = 1200 kPa = 0.12 MPa

1.3 Bar0

1.3 Bar = 1300 millibars = 19.12 psi = 1300 kPa = 0.13 MPa

1.4 Bar0

1.4 Bar = 1400 millibars = 20.59 psi = 1400 kPa = 0.14 MPa

1.5 Bar0

1.5 Bar = 1500 millibars = 22.07 psi = 1500 kPa = 0.15 MPa

1.6 Bar0

1.6 Bar = 1600 millibars = 23.54 psi = 1600 kPa = 0.16 MPa

2 Bar0

2 Bar = 2000 millibars = 29.42 psi = 2000 kPa = 0.2 MPa

2.5 Bar0

2.5 Bar = 2500 millibars = 36.78 psi = 2500 kPa = 0.25 MPa

3 Bar0

3 Bar = 3000 millibars = 44.13 psi = 3000 kPa = 0.3 MPa

3.5 Bar0

3.5 Bar = 3500 millibars = 51.49 psi = 3500 kPa = 0.35 MPa

4 Bar0

4 Bar = 4000 millibars = 58.84 psi = 4000 kPa = 0.4 MPa

4.5 Bar0

4.5 Bar = 4500 millibars = 66.20 psi = 4500 kPa = 0.45 MPa

5 Bar0

5 Bar = 5000 millibars = 73.55 psi = 5000 kPa = 0.5 MPa

5.5 Bar0

5.5 Bar = 5500 millibars = 80.91 psi = 5500 kPa = 0.55 MPa

6 Bar0

6 Bar = 6000 millibars = 88.26 psi = 6000 kPa = 0.6 MPa

6.5 Bar0

6.5 Bar = 6500 millibars = 95.62 psi = 6500 kPa = 0.65 MPa

7 Bar0

7 Bar = 7000 millibars = 102.97 psi = 7000 kPa = 0.7 MPa

7.5 Bar0

7.5 Bar = 7500 millibars = 110.33 psi = 7500 kPa = 0.75 MPa

8 Bar0

8 Bar = 8000 millibars = 117.68 psi = 8000 kPa = 0.8 MPa

8.5 Bar0

8.5 Bar = 8500 millibars = 125.04 psi = 8500 kPa = 0.85 MPa

9 Bar0

9 Bar = 9000 millibars = 132.39 psi = 9000 kPa = 0.9 MPa

10 Bar0

10 Bar = 147.1 psi = 1 MPa

12 Bar0

12 Bar = 176.52 psi = 1.2 MPa

13 Bar0

13 Bar = 191.23 psi = 1.3 MPa

14 Bar0

14 Bar = 205.94 psi = 1.4 MPa

15 Bar0

15 Bar = 220.65 psi = 1.5 MPa

16 Bar0

16 Bar = 235.36 psi = 1.6 MPa

17 Bar0

17 Bar = 250.07 psi = 1.7 MPa

18 Bar0

18 Bar = 264.78 psi = 1.8 MPa

20 Bar0

20 Bar = 294.2 psi = 2 MPa

25 Bar0

25 Bar = 367.8 psi = 2.5 MPa

30 Bar0

30 Bar = 441.3 psi = 3 MPa

35 Bar0

35 Bar = 514.9 psi = 3.5 MPa

40 Bar0

40 Bar = 588.4 psi = 4 MPa

50 Bar0

50 Bar = 735.5 psi = 5 MPa

60 Bar0

60 Bar = 882.6 psi = 6 MPa

64 Bar0

64 Bar = 941.4 psi = 6.4 MPa

70 Bar0

70 Bar = 1029.7 psi = 7 MPa

80 Bar0

80 Bar = 1176.8 psi = 8 MPa

90 Bar0

90 Bar = 1323.9 psi = 9 MPa

100 Bar0

100 Bar = 1471 psi = 10 MPa

120 Bar0

120 Bar = 1765.2 psi = 12 MPa

130 Bar0

130 Bar = 1912.3 psi = 13 MPa

135 Bar0

140 Bar0

140 Bar = 2059.4 psi = 14 MPa

150 Bar0

150 Bar = 2206.5 psi = 15 MPa

160 Bar0

160 Bar = 2353.6 psi = 16 MPa

200 Bar0

200 Bar = 2942 psi = 20 MPa

225 Bar0

225 Bar = 3309.75 psi = 22.5 MPa

270 Bar0

270 Bar = 3971.7 psi = 27 MPa

300 Bar0

300 Bar = 4413 psi = 30 MPa

350 Bar0

350 Bar = 5148.5 psi = 35 MPa

400 Bar0

400 Bar = 5884 psi = 40 MPa

Seals

CR0

CR or Chloroprene, excellent resistance to weathering, ozone, heat, oil, and various chemicals. -40°C to +121°C

ECO0

ECO – Epichlorohydrin Rubber (Epichlorohydrin - or Herchlor, Gechron or Hydrin). excellent resistance to acids, alkali's and ozone -35°C to +125°C

EPDM0

EPDM (Ethylene Propylene Diene Monomer) - known as Ethylene Propylene terpolymer, Buna-AP, Dutral, Polysar-EDM, Royalene, Vistalon, Keltan, Epcar, Nordel or Epsyn). Good for hot and drinking water, Steam, Freon refrigerant gas and Air -40°C to +120°C (+150°C steam) Poor resistance to oils + fuels

FKM (Viton)0

FKM Fluoro elastomer (Fluorocarbon) Viton® Dupont registered, known as Tecnoflon, Fluorel, Dai-El. Good for hot water, acid, alkali, oils, hydrocarbons and salt solutions, many aggressive chemicals, diluted acids, weak alkali's, mineral oils, aliphatic and aromatic hydrocarbons, chlorinated hydrocarbons, sunlight and ozone. -26°C to +205°C. Poor resistance to Ketone's and Acetone.

HNBR0

HNBR (Hydrogenated Nitrile Butadine Rubber) also known as Therban, Zetpol or Tornac). Good for motor oils, sour gas, amine oil mixtures, oxidised fuels, lubricating oils, mineral based hydraulic oil, animal and vegetable oil, diesel fuel, ozone, dilute acids and bases, new bio-oils, H2S Hydrogen Sulphide and C02 carbon dioxide. -40°C to +150°C. Poor for concentrated alkali's, esters, alkyl phosphate, ethers, halogenated solvents, ketone's, halogenated hydrocarbons, solvents and flames.

Hypalon0

Hypalon is a chlorosulfonated polyethylene (CSPE) synthetic rubber (CSM). Good for chemicals, ozone, ultraviolet light, oxidising agents, hot water, corrosive chemicals, low gas permeability, good electrical properties, low flammability. -35°C to +125°C. Poor to fair fuel resistance and its low temperature properties are generally limited.

NBR0

NBR (Nitrile Buna Rubber) known as Nitrile Butadine, Buna-N, Hycar, Chemigum, Butakon, Breaon, Butacril, Paracil, Nipol, Perbunan, Krynac or Europrene-N. Good for Aliphatic Hydrocarbons, Petroleum, Fuels, Mineral Oil, Vegetable and Hydraulic Oil, Alcohol and many Acids. -35°C to +100°C. Poor for Ozone, Acetone, Methyl ethyl Ketone, Chlorinated Hydrocarbons, Ethers and Esters.

Neoprene0

Neoprene known as CR or Chloroprene. Good resistance to Freon and ammonia, flames, excellent UV resistance, Ozone, oxygen and sunlight, tough, abrasion resistant and has a low compression set with an outstanding ability to adhere to metals. -20°C to +110°C.

PTFE (Teflon)0

PTFE (Polytetrafluoroethylene) also known as Teflon® Dupont registered. Excellent resistance to almost every fluid or gas. -200°C to +230°C

Silicone0

Silicone (VMQ) known as PVMQ, Silastic, Siloprene, Rhodorsil or Silplus. Good resistance to Oil, solvents, aniline alcohol, dilute acids or bases, benzene, toluene, petrol. -60°C to +230°C. Poor resistance Diesel, hot air, steam over 150 C, strong acids and bases.

VST0

VST (Viton-Silicone-Teflon). Has enhanced chemical resistance compared to Viton, especially against aggressive chemicals like ketones, esters, and some organic acids. Combines the properties of Viton, silicone, and Teflon, offering improved flexibility, compression set resistance, and low-temperature performance compared to standard Viton. -40°C to 200°C

Voltage

3vDC0

3 volts Direct Current for 2x 1.5v AA batteries

6vDC0

6 volts Direct Current

12vDC0

12 volts Direct Current

12vAC0

12 volts 50/60Hz Alternating Current

24vDC0

24 volts Direct Current

24vAC0

24 volts 50/60Hz Alternating Current

36vAC0

36 volts 50/60Hz alternating current

48vAC0

48 volts 50/60Hz alternating current

48vDC0

48 volts Direct Current

110vAC0

110 volts 50/60Hz Alternating Current

110vDC0

110 volts Direct Current

125vDC0

125 volts Direct Current

230VAC0

230 volts 50/60Hz Alternating Current

200vDC0

200 volts Direct Current

380vAC0

380 volts 50/60Hz Alternating Current

Approval: ATEX,WRAS,IP etc

ATEX Zone II GD0

hazardous area classification indicating a potentially explosive atmosphere with gases and dust present, requiring specific equipment for safe operation.

ATEX ExnA0

certifies equipment for use in potentially explosive atmospheres, indicating it is designed to prevent ignition sources, minimizing risk.

ATEX Exm0

ATEX Protection by encapsulation ll 2 G Ex mb ll T4 Gb and ll 2 D Ex tb IIIC T130°C Db IP65

ATEX Exd0

ATEX Protection by enclosure, EEx d IIC T flameproof solenoid coil

ATEX Exia0

ATEX protection by intrinsic safety, II 2 G Ex ia IIB/IIC T4 or T6.

IP400

Protected against solid foreign objects of 1mm diameter and more and no protection against water ingress.

IP540

Dust protected and protected against splashing water

IP650

Dust tight and protected against water jets

IP660

Dust protected and protected against powerful water jets.

IP670

Dust protected and protected against immersion in water

IP680

Dust protected and protected against the effects of continuous immersion in water.

CSA0

CSA approval certifies products for safety and performance, conducted by the Canadian Standards Association.

EN12021 Breathing Air0

EN12021 approval certifies compressed air quality for breathing apparatus, ensuring it meets safety standards for human respiratory use.

EN1610

EN161 approval is a European standard for gas safety shut-off valves, ensuring they meet specified safety and performance criteria.

UL0

UL (Underwriters Laboratories) approval indicates that a product has met safety standards set by UL for electrical devices and components.

WRAS0

WRAS approval ensures water fittings meet UK water regulations, safeguarding public health by preventing contamination, waste, and misuse of water supplies.

Orifice

0.6mm0

Valve orifice or sealing face with diameter 0.6mm

0.8mm0

Valve orifice or sealing face with diameter 0.8mm

1.0mm0

Valve orifice or sealing face with diameter 1mm

1.2mm0

Valve orifice or sealing face with diameter 1.2mm

1.3mm0

Valve orifice or sealing face with diameter 1.3mm

1.5mm0

Valve orifice or sealing face with diameter 1.5mm

1.6mm0

Valve orifice or sealing face with diameter 1.6mm

1.8mm0

Valve orifice or sealing face with diameter 1.8mm

2.0mm0

Valve orifice or sealing face with diameter 2mm

2.3mm0

Valve orifice or sealing face with diameter 2.3mm

2.4mm0

Valve orifice or sealing face with diameter 2.4mm

2.5mm0

Valve orifice or sealing face with diameter 2.5mm

3.0mm0

Valve orifice or sealing face with diameter 3mm

3.5mm0

Valve orifice or sealing face with diameter 3.5mm

4.0mm0

Valve orifice or sealing face with diameter 4mm

4.5mm0

Valve orifice or sealing face with diameter 4.5mm

5.0mm0

Valve orifice or sealing face with diameter 5

5.5mm0

Valve orifice or sealing face with diameter 5.5mm

6.0mm0

Valve orifice or sealing face with diameter 6mm

6.5mm0

Valve orifice or sealing face with diameter 6.5mm

7mm0

Valve orifice or sealing face with diameter 7mm

7.5mm0

Valve orifice or sealing face with diameter 7.5

8.0mm0

Valve orifice or sealing face with diameter 8mm

9.0mm0

Valve orifice or sealing face with diameter 9mm

10mm0

Valve orifice or sealing face with diameter 10mm

11mm0

Valve orifice or sealing face with diameter 11mm

12mm0

Valve orifice or sealing face with diameter 12mm

13mm0

Valve orifice or sealing face with diameter 13mm

15mm0

Valve orifice or sealing face with diameter 15mm

17mm0

Valve orifice or sealing face with diameter 17mm

18mm0

Valve orifice or sealing face with diameter 18mm

20mm0

Valve orifice or sealing face with diameter 20mm

22mm0

Valve orifice or sealing face with diameter 22mm

23mm0

Valve orifice or sealing face with diameter 23mm

24mm0

Valve orifice or sealing face with diameter 24mm

25mm0

Valve orifice or sealing face with diameter 25mm

27mm0

Valve orifice or sealing face with diameter 27mm

30mm0

Valve orifice or sealing face with diameter 30mm

32mm0

Valve orifice or sealing face with diameter 32mm

35mm0

Valve orifice or sealing face with diameter 35mm

38mm0

Valve orifice or sealing face with diameter 38mm

40mm0

Valve orifice or sealing face with diameter 40mm

45mm0

Valve orifice or sealing face with diameter 45mm

50mm0

Valve orifice or sealing face with diameter 50mm

55mm0

Valve orifice or sealing face with diameter 55mm

57mm0

Valve orifice or sealing face with diameter 57mm

59mm0

65mm0

Valve orifice or sealing face with diameter 65mm

72mm0

Valve orifice or sealing face with diameter 72mm

76mm0

80mm0

Valve orifice or sealing face with diameter 80mm

95mm0

125mm0

Valve orifice or sealing face with diameter 125mm

150mm0

Valve orifice or sealing face with diameter 150mm

200mm0

Valve orifice or sealing face with diameter 200mm

250mm0

Valve orifice or sealing face with diameter 250mm

300mm0

Valve orifice or sealing face with diameter 300mm

350mm0

Valve orifice or sealing face with diameter 350mm

400mm0

Valve orifice or sealing face with diameter 400mm

450mm0

Valve orifice or sealing face with diameter 450mm

500mm0

Valve orifice or sealing face with diameter 500mm

Operation

Assisted Lift0

Assisted lift solenoid valve assists in opening against pressure, ensuring reliable operation from vacuum to medium pressure systems.

Direct Acting0

Directly controls flow without external pressure assistance operates from vacuum upwards.

Pressure Assisted0

Operate via pilot pressure control and require a minimum pressure difference between inlet and outlet from 0.5 Bar.

Options required

Anti Water Hammer0

Prevents or reduces water hammer caused by sudden changes in fast moving fluid flow.

Banjo0

allows fluid to flow through the central hole in the banjo bolt and exit through the radial holes, facilitating connections in tight spaces or where angular adjustments are needed

Bi-Directional Flow0

Can control flow in both directions

Degreased0

Oil and grease removed typically for oxygen or paint spray use.

Flow Control0

Flow regulation to control the amount of flow.

Manifold0

A group of multiple valves together on one manifold, simple layout streamline control and space saving.

Manual Control0

Valves that require manual input to operate such as lever, button or switch

Manual Override0

A facility to manually move the valve into the fully actuated position via a button, lever or key.

Mounting Bracket0

Valve has the facility to be supplied with a bracket for mounting and securing.

Mounting Holes0

Supplied with additional threaded holes typically in the base, typically for securing to a baseplate.

Outlet - right angle0

The outlet port is at right angles to inlet port, ideal for space efficiency.

Panel Mount0

Valve is designed to be mounted and secured into an instrument panel

Position Feedback Closed0

The valve is equipped with an additional volt free electrical switch that is triggered when the valve is mechanically closed.

Position Feedback Open+Closed0

The valve is equipped with two additional volt free electrical switches that are triggered when the valve is mechanically closed or open position.

Position proximity switch - Open0

The valve is equipped with an additional volt free electrical switch that is triggered as the valve reaches the open position.

Position indication Visual 0

The valve is equipped with clear cover or dome under which an arrow or flag can be seen to confirm either the open and or closed position of the valve.

Shading Ring - Silver0

The copper shading ring in the solenoid tube has been replaced with silver. Typically used for RO water and aggressive media applications.

Shading Ring - without0

The copper shading ring in the solenoid tube has been removed, for DC voltages only and typically for aggressive media applications.

Speed controller0

A unidirectional speed controller regulates fluid or gas flow in one direction only, often used in pneumatic systems for precise control.

Y Pattern0

A Y-pattern valve is a valve with a Y-shaped body design, typically used for high-pressure applications to reduce pressure drop and turbulence, often found in steam systems.

Spares (Coils, Connectors, Seals)

Actuator Head Air + Motor0

Air Actuator0

Armature Assembly0

Blanking Plug0

Coil bore 7mm0

Coil bore 9mm0

Coil bore 10mm0

Coil bore 12mm0

Coil bore 13mm0

Coil bore 14mm0

Coil bore 15mm0

Coil bore 16mm0

Coil bore 17mm0

Coil bore 18mm0

Coil bore 20mm0

Coil bore 20mm+0

Coil Commisioning Magnet0

DIN connector Form A0

DIN connector Form B Industrial0

DIN connector Form B0

DIN connector Form C0

Fittings0

FRL Spares (Bowls filters etc)0

Manifold0

Mounting Bracket0

Nuts + bolts + plates0

Position switch0

Pressure Gauge0

Pressure reducing controller0

Pressure relief controller0

Pressure sustaining controller0

Seals0

Springs0

Valve Cover0

Only Show Items In Stock

Hide spare parts

Showing 1 - 20 of 469 total products

*On Sale* M5-1/2 BSP Male stud pushin tube fitting 4-12mm £1.30 £0.61 inc VAT

1392 IN STOCK

*On Sale* M5-1/2 BSP Male stud elbow pushin fitting 4-12mm £2.11 £0.61 inc VAT

600 IN STOCK

Solenoid valve commissioning magnet (1.5KG Pull) 10 15 18mm £59.90 £19.80 inc VAT

517 IN STOCK

Solenoid timer 20mSec-60Min ON 30Sec-12Hrs Off Repeat Form A £69.41 £20.00 inc VAT

528 IN STOCK

Polyurethane tube 50-200mtr rolls all metric sizes + colours £37.71 £18.85 inc VAT

178 IN STOCK

Solenoid Coil Core 14.6mm, H 42mm, W 30mm, L 39mm 15W IP65 £42.86 £30.00 inc VAT

9318 IN STOCK

Breathing air filter element 5μPE Coalescing Carbon 1/4-1/2 £59.90 £38.94 inc VAT

75 IN STOCK

Solenoid valve commissioning magnet (40KG Pull) 20mm Bore £97.42 £43.20 inc VAT

15 IN STOCK

Emergency electrical STOP button Open+Close switch 400v 10A £24.34 £10.86 inc VAT

441 IN STOCK

Solenoid Coil Core 16mm, H40.5mm, W41.5mm, L59mm 18W IP68 £38.95 £31.58 inc VAT

313 IN STOCK

1/8, 1/4, BSP Male Hex blanking plugs nickle plated brass £0.43 inc VAT

267 IN STOCK

Solenoid Coil Core 10mm, H 29.7mm, L 27.5mm, W 22mm 5.5W £21.68 £15.98 inc VAT

142 IN STOCK

1/4 Air valve 0-9 Bar 3/2 button, twist + mechanical control £31.75 £26.89 inc VAT

66 IN STOCK

Electrical DIN Connector 2P+E Form A LED PG9 (6-8mm) IP67 £5.33 £3.86 inc VAT

816 IN STOCK

*On Sale* Union straight pushin airline fitting 4mm to 12mm £2.71 £0.43 inc VAT

483 IN STOCK

*On Sale*M5-1/2BSP Male swivel elbow speed controller 4-12mm £8.72 £2.05 inc VAT

210 IN STOCK

Digital Timer 1Sec-100Hrs ON/OFF OFF/ON + Single Shot FORM A £105.50 £20.00 inc VAT

170 IN STOCK

Solenoid coil core 9/8mm, H 29.5mm, W 22mm, L 28.8mm 4.5W £14.21 £13.19 inc VAT

2200 IN STOCK

*On Sale* M5-1/2BSP Male Elbow swivel pushin fitting 4-12mm £3.18 £2.05 inc VAT

555 IN STOCK

*On Sale* M5-1/2 BSP Extended male elbow fitting 4-12mm £2.99 £1.04 inc VAT

108 IN STOCK

1
2
3
4
...
23
Last

Contact

08:00 - 17:30

Contact Us

Address

Unit 3, Rainbow Court
Armstrong Way
Great Western Business Park
Yate, Bristol, BS37 5NG
United Kingdom
sales@solenoid-valves.com

My Account

Login Orders Register

Company

About Us Returns Payment Options FAQs

Quick Links

ATEX Valves Search by Brand Breathing Air Filters High Pressure Valves Clearance Items WRAS Valves New Products Information Chemical Compatibility Guide

Members of the British Valve and Actuator Association Site Verified by Security Metrics

Trademark of Connexion Developments Ltd

#UK00003734167

Privacy Policy Terms & Conditions Cookie Policy

© 2025 Connexion Developments Ltd, All rights reserved.