Description
Pre-Wired DIN Form B 11mm Connector 250V 10A IP67
Nass Magnet moulded pre-wired DIN Form B Industrial 11mm electrical connector, supplied with a choice of 2 metre or 5 metre black cable for fast and reliable solenoid valve installation.
This is the no-circuit version, containing no LED, VDR / varistor or rectifier. This allows the connector to be used with AC or DC supplies up to 250V, subject to the connected solenoid coil having the correct voltage rating.
Rated at an impressive 10A maximum, the connector is factory moulded onto 3-core 0.75mm² H05VVF cable and provides IP67 protection when correctly plugged and secured.
The combination of pre-wired construction, integrated gasket and IP67 protection makes it particularly suitable for industrial solenoid valve installations where a robust ready-to-connect electrical assembly is preferred.
Available Cable Lengths
2 Metre Cable
Nass Magnet: 612-202-0162
5 Metre Cable
Nass Magnet: 612-202-0164
Electrical Specification
Connector: DIN Form B Industrial
Contact distance: 11mm
Connection: 2P + PE
Protective earth position: 12h
Maximum voltage: 250V
Current type: AC/DC
Maximum current: 10A
Internal circuit: None
LED: None
VDR / Varistor: None
Rectifier: None
Contacts: CuZn, zinc plated
Contact resistance: <4mΩ
No Internal Circuit
This version provides a direct electrical connection without additional electronic components.
There is:
✓ No LED indicator
✓ No VDR / varistor
✓ No diode
✓ No bridge rectifier
The absence of voltage-specific electronics allows the connector itself to be used across a broad range of AC or DC supplies up to 250V.
The connected solenoid coil must always be correctly rated for the actual supply voltage.
Pre-Wired 2m or 5m Cable
Cable type: H05VVF
Cable colour: Black
Number of cores: 3
Conductor cross-section: 0.75mm²
Core colours: Green/yellow, brown and blue
Cable lengths: 2m or 5m
Stripped cable end: 30mm
Loose end: Sleeved
The 2m and 5m versions use the same cable specification.
Moulded IP67 Construction
Unlike a conventional field-wireable DIN connector, this version is factory moulded directly onto the cable.
Overmoulding material: PUR
Overmoulding colour: Black
Terminal block: PA6 GF30
Gasket: Integrated
Central fixing screw: M3 × 24mm
Fixing screw material: Zinc-plated steel 4.8
Tightening torque: 0.4 ±0.1Nm
The integrated gasket and moulded cable entry remove the separate cable gland used on field-wireable connectors.
IP67 Protection
Protection rating: IP67 to DIN EN 60529
Important: IP67 applies in the “plugged and screwed condition”.
Ambient operating temperature is −25°C to +90°C, and the connector is RoHS compliant.
DIN Form B Industrial 11mm Connection
This connector uses the 11mm Industrial Form B contact arrangement.
It should not be confused with the 10mm Form B analogue connector. Customers should confirm the contact spacing of the solenoid coil before ordering.
Typical Applications
✓ Solenoid valves
✓ Pneumatic directional valves
✓ Hydraulic valves
✓ Process control valves
✓ Industrial automation
✓ PLC controlled valves
✓ Water control equipment
✓ OEM machinery
✓ Packaging machinery
✓ Factory automation
Why Choose the Pre-Wired Version?
The moulded connector provides a ready-to-install alternative to a conventional field-wireable DIN plug.
There is no cable gland to assemble and no conductors to terminate inside the connector. The factory-moulded construction also provides IP67 environmental protection, while the integrated gasket provides sealing at the mating interface.
With a 10A maximum current rating, up to 250V AC/DC capability and choice of 2m or 5m cable, this is a particularly versatile general-purpose pre-wired connector for Industrial Form B solenoid valves.
Related Products & Categories
