air actuated valves that utilise a compressed air supply to operate.

compressed air line tubing and push to connect fittings

Check + non return valves only allow flow in one direction

Automated + time control drain valves

Flow regulating valves with manual or electric modulating 4-20mA control.

3/2 + 5/2 foot pedal air control valves for pneumatic cylinders and systems.

3/2 + 5/2 way air valves controlled by a Finger or Palm Button

Air valves that are controlled manually

3/2 and 5/2 air control valves that require users to twist a button

Air control valves operate with a manual lever. 3/2, 5/2, 5/3, 4/2 + 4/3 way

2/2, 3/2, 5/2 mechanical air control valves for automated pneumatic systems.

Will instantly open outlet to exhaust when the inlet pressure drops to greatly increase cylinder reaction speed.

Safety shut off isolation valve, shuts off and secures air line systems, will vent downstream air when closed.

Incorporates a check ball valve to allow pressure in a line to be obtained from two sources.

Electric open and close control for airline systems, power off downstream air is vented to atmosphere - power on opens slowly to prevent sudden pressure surges.

Valves controlled by electrical signal via a solenoid or electro magnet.

Time control valves can be set to activate according to preset intervals when power is applied.

2 ports (inlet/outlet) with 2 positions (Open/Closed) - valve stays closed (Failsafe) requires power to open

3 ports with 2 positions. Power off inlet closed, outlet open to exhaust - power on inlet open to outlet with exhaust closed.

3 ports 2 positions. Inlet open to outlet with exhaust closed - power on inlet closed with outlet open to exhaust.

A 4/2 way valve has four ports and two positions. It controls the direction of flow by switching between two paths in a pneumatic or hydraulic system.

A 4/3 way valve has four ports and three positions. It controls the direction of flow by switching between two paths in a pneumatic or hydraulic system with third option all ports closed.

5 ports 2 positions (1 inlet, 2 outlets, 2 exhaust ports). Power to coil Cylinder fully extends - Power off cylinder fully retracts (or visa versa)

Power to left coil Cylinder fully extends, power to right coil cylinder fully retracts, power off cylinder stays put fully extended or retracted.

Power to left coil cylinder extends, power to right coil cylinder retracts, power off cylinder stays put even in a mid position.

0.02 Bar = 20 millibars = 0.29psi = 2 Kpa

0.1 Bar = 100 millibars = 1.47 psi = 1kPa

0.2 Bar = 200 millibars = 2.94 psi = 20kPa

0.3 Bar = 300 millibars = 4.41 psi = 30 kPa

0.4 Bar = 400 millibars = 4.41 psi = 40 kPa

0.5 Bar = 500 millibars = 7.36 psi = 50 kPa

0.6 Bar = 600 millibars = 8.83 psi = 60 kPa

0.7 Bar = 700 millibars = 10.3 psi = 70 kPa

0.8 Bar = 800 millibars = 11.77 psi = 80 kPa

1 Bar = 1000 millibars = 14.71 psi = 100 kPa = 0.1 MPa

1.2 Bar = 1200 millibars = 17.65 psi = 1200 kPa = 0.12 MPa

1.3 Bar = 1300 millibars = 19.12 psi = 1300 kPa = 0.13 MPa

1.4 Bar = 1400 millibars = 20.59 psi = 1400 kPa = 0.14 MPa

1.5 Bar = 1500 millibars = 22.07 psi = 1500 kPa = 0.15 MPa

1.6 Bar = 1600 millibars = 23.54 psi = 1600 kPa = 0.16 MPa

2 Bar = 2000 millibars = 29.42 psi = 2000 kPa = 0.2 MPa

2.5 Bar = 2500 millibars = 36.78 psi = 2500 kPa = 0.25 MPa

3 Bar = 3000 millibars = 44.13 psi = 3000 kPa = 0.3 MPa

3.5 Bar = 3500 millibars = 51.49 psi = 3500 kPa = 0.35 MPa

4 Bar = 4000 millibars = 58.84 psi = 4000 kPa = 0.4 MPa

4.5 Bar = 4500 millibars = 66.20 psi = 4500 kPa = 0.45 MPa

5 Bar = 5000 millibars = 73.55 psi = 5000 kPa = 0.5 MPa

5.5 Bar = 5500 millibars = 80.91 psi = 5500 kPa = 0.55 MPa

6 Bar = 6000 millibars = 88.26 psi = 6000 kPa = 0.6 MPa

6.5 Bar = 6500 millibars = 95.62 psi = 6500 kPa = 0.65 MPa

7 Bar = 7000 millibars = 102.97 psi = 7000 kPa = 0.7 MPa

7.5 Bar = 7500 millibars = 110.33 psi = 7500 kPa = 0.75 MPa

8 Bar = 8000 millibars = 117.68 psi = 8000 kPa = 0.8 MPa

8.5 Bar = 8500 millibars = 125.04 psi = 8500 kPa = 0.85 MPa

9 Bar = 9000 millibars = 132.39 psi = 9000 kPa = 0.9 MPa

10 Bar = 147.1 psi = 1 MPa

12 Bar = 176.52 psi = 1.2 MPa

13 Bar = 191.23 psi = 1.3 MPa

14 Bar = 205.94 psi = 1.4 MPa

15 Bar = 220.65 psi = 1.5 MPa

16 Bar = 235.36 psi = 1.6 MPa

17 Bar = 250.07 psi = 1.7 MPa

18 Bar = 264.78 psi = 1.8 MPa

20 Bar = 294.2 psi = 2 MPa

EPDM (Ethylene Propylene Diene Monomer) - known as Ethylene Propylene terpolymer, Buna-AP, Dutral, Polysar-EDM, Royalene, Vistalon, Keltan, Epcar, Nordel or Epsyn). Good for hot and drinking water, Steam, Freon refrigerant gas and Air -40°C to +120°C (+150°C steam) Poor resistance to oils + fuels

FKM Fluoro elastomer (Fluorocarbon) Viton® Dupont registered, known as Tecnoflon, Fluorel, Dai-El. Good for hot water, acid, alkali, oils, hydrocarbons and salt solutions, many aggressive chemicals, diluted acids, weak alkali's, mineral oils, aliphatic and aromatic hydrocarbons, chlorinated hydrocarbons, sunlight and ozone. -26°C to +205°C. Poor resistance to Ketone's and Acetone.

HNBR (Hydrogenated Nitrile Butadine Rubber) also known as Therban, Zetpol or Tornac). Good for motor oils, sour gas, amine oil mixtures, oxidised fuels, lubricating oils, mineral based hydraulic oil, animal and vegetable oil, diesel fuel, ozone, dilute acids and bases, new bio-oils, H2S Hydrogen Sulphide and C02 carbon dioxide. -40°C to +150°C. Poor for concentrated alkali's, esters, alkyl phosphate, ethers, halogenated solvents, ketone's, halogenated hydrocarbons, solvents and flames.

NBR (Nitrile Buna Rubber) known as Nitrile Butadine, Buna-N, Hycar, Chemigum, Butakon, Breaon, Butacril, Paracil, Nipol, Perbunan, Krynac or Europrene-N. Good for Aliphatic Hydrocarbons, Petroleum, Fuels, Mineral Oil, Vegetable and Hydraulic Oil, Alcohol and many Acids. -35°C to +100°C. Poor for Ozone, Acetone, Methyl ethyl Ketone, Chlorinated Hydrocarbons, Ethers and Esters.

hazardous area classification indicating a potentially explosive atmosphere with gases and dust present, requiring specific equipment for safe operation.

ATEX Protection by encapsulation ll 2 G Ex mb ll T4 Gb and ll 2 D Ex tb IIIC T130°C Db IP65

ATEX protection by intrinsic safety, II 2 G Ex ia IIB/IIC T4 or T6.

Dust tight and protected against water jets

Valve orifice or sealing face with diameter 0.8mm

Valve orifice or sealing face with diameter 1mm

Valve orifice or sealing face with diameter 1.1mm

Valve orifice or sealing face with diameter 1.2mm

Valve orifice or sealing face with diameter 1.3mm

Valve orifice or sealing face with diameter 1.4mm

Valve orifice or sealing face with diameter 1.5mm

Valve orifice or sealing face with diameter

Valve orifice or sealing face with diameter 2.2mm

Valve orifice or sealing face with diameter 2.5mm

Valve orifice or sealing face with diameter 2.6mm

Valve orifice or sealing face with diameter 3mm

Valve orifice or sealing face with diameter 3.5mm

Valve orifice or sealing face with diameter 4mm

Valve orifice or sealing face with diameter 4.5mm

Valve orifice or sealing face with diameter 5

Valve orifice or sealing face with diameter 5.5mm

Valve orifice or sealing face with diameter 6mm

Valve orifice or sealing face with diameter 6.5mm

Valve orifice or sealing face with diameter 7mm

Valve orifice or sealing face with diameter 7.5

Valve orifice or sealing face with diameter 8mm

Valve orifice or sealing face with diameter 9mm

Valve orifice or sealing face with diameter 9.5mm

Valve orifice or sealing face with diameter 11mm

Valve orifice or sealing face with diameter 12mm

Valve orifice or sealing face with diameter 13mm

Directly controls flow without external pressure assistance operates from vacuum upwards.

Operate via pilot pressure control and require a minimum pressure difference between inlet and outlet from 0.5 Bar.

6 volts Direct Current

12 volts Direct Current

12 volts 50/60Hz Alternating Current

24 volts Direct Current

24 volts 50/60Hz Alternating Current

48 volts 50/60Hz alternating current

48 volts Direct Current

110 volts 50/60Hz Alternating Current

110 volts Direct Current

230 volts 50/60Hz Alternating Current

200 volts Direct Current

allows fluid to flow through the central hole in the banjo bolt and exit through the radial holes, facilitating connections in tight spaces or where angular adjustments are needed

Flow regulation to control the amount of flow.

A group of multiple valves together on one manifold, simple layout streamline control and space saving.

Valves that require manual input to operate such as lever, button or switch

A facility to manually move the valve into the fully actuated position via a button, lever or key.

Valve has the facility to be supplied with a bracket for mounting and securing.

Supplied with additional threaded holes typically in the base, typically for securing to a baseplate.

The outlet port is at right angles to inlet port, ideal for space efficiency.

Valve is designed to be mounted and secured into an instrument panel

A unidirectional speed controller regulates fluid or gas flow in one direction only, often used in pneumatic systems for precise control.